Project Gallery

Installing a Mosaic Tile Backsplash

May 2, 2017

I have always thought my mother’s kitchen is gorgeous.  But guys, we just took it to a whole new level this weekend.  She now has a beautiful backsplash – that we installed by ourselves! In ONE day.  So if your excuse for not having a backsplash in your kitchen is that it’s too hard – I’m not letting you get away with that anymore!

Tools you need: 

TileQu!ck Wall Tile Adhesive Mat – from Menards (a must!)

Pre-Mixed Grout

Tile (12×12 mosaic tiles squares is what we used)

Wet Tile Saw

Outlet extenders

Grouting float

Sponge

 

To start, make sure the area you are tiling is clean and smooth (or as smooth as possible).  We tiled over an area that was already textured and it seemed to work fine!

tile2

Next, turn off the power to the outlets, and unscrew outlets from the wall.  You will need to pull them out slightly to install the extenders.

The outlet extenders should slip over the outlets.  Our preference was the blue extenders because they are more shallow.  They did the trick, and were much easier to slip over the outlets.  Keep the long screws that come with the extenders and let the outlets hang out until you are done tiling.  Screwing the outlets, extenders, and outlet covers in over the tile will be the last thing you do.

IMG_0135  IMG_0126

Next, measure and cut the TileQu!ck to cover the area you are tiling.  We cut this using a linoleum knife and T-square.  It comes in a roll 18″ x 10′ long, which perfectly did the entire kitchen for us.

tile1 nonweb

IMG_0122

**Honestly, I wouldn’t have attempted this project without TileQu!ck.  It saved so much time and mess!  If you are going to be using mortar to attach your tile, then this is not the tutorial for that!

Peel off the backing on the TileQu!ck mat, and apply to the wall.  We rolled over the mat with a small rolling pin to make sure it was really stuck.

tile5

Now for the fun part.  The kitchen changes so quickly!

The tiles come in 12×12 squares with uneven sides.

IMG_0127

This makes it easy to place them next to each other without seams, but you will need to cut the first square down to create a straight edge.

IMG_0136

To cut the tiles, use a wet saw.  Basically, this a saw that cools the diamond blade with water underneath to prevent chipping the glass tile too badly.

We bought the QEP 4″ Torque Master XT Portable Tile Wet Saw for $30 at Menards.

IMG_0128

If you are planning on doing a larger project, this may not be the most durable option.  But it did the job for us!  Make sure you create a drip loop in the power cord and add water to the bottom of the saw according to the directions – do not let the saw run dry.  

Now for the tricky part- the outlets.

To cut around outlets, we made cuts with the linoleum knife in between the tile rows closest to the top and bottom of the outlet.

**We found that our mosaic tile was pretty much made for outlets.  The measurements for the top and bottom of the outlets almost always fell between two rows of tile. Super nice!

IMG_0139
This is marking off the top and bottom of the outlet. See how it falls neatly between the rows!

 

This doesn’t have to be an exact science either, because outlet covers and grout fill a lot of these spaces.  If you are not using the same small mosaic tile we used, then you may end up cutting your tiles length wise to fit.

**We found that our mosaic tile was pretty much made for outlets.  The measurements for the top and bottom of the outlets almost always fell between two rows of tile. Super nice!

IMG_0140
Such cute hands. 🙂

Once you have cut in between the rows, it is easy to peel back the tile and only make a cut along the side of the outlet.

IMG_0143

Your tile square will end up being stuck to the wall in two pieces around the outlet, but this seemed like the easiest way to do it!

You may need to fill in small gaps with leftover glass tile pieces, so save the outlet cutouts because they will come in handy.

Also, our backsplash area was 13.5 inches high, so to cover the top inch and a half, we cut off individual rows of tile to fill in as needed.

When you have finished covering the entire area with tile, grout immediately.  We used TEC Ready to Use Pre-Mixed Grout in the Coffee color from Menards.  Place a fair amount grout on the edge of the float.

IMG_0149
These pictures got a little blurry. She was moving too quickly for me!

Apply by wiping top to bottom along the tile to start.  This pushes the grout into the cracks!  Then, wipe the grout side to side and thoroughly over entire area.

IMG_0151  IMG_0150

When you are done grouting, use a damp sponge to scrub off any excess.  Finally, run a damp cloth over tile to remove any remaining grout.

IMG_0157
This is the tiles after the sponge scrubbing, but before the final wipe with a damp cloth. Not quite shiny yet!

Let dry, and screw outlets, extenders, and outlet covers into the wall over the tile.

IMG_0168

IMG_0170

Stand back, have a glass or two of wine, and admire your work – you’re done!

tile 3

If you want to check out another idea for an easy backsplash, check out my Faux Brick Backsplash post.

 

 

 

 

Continue Reading